Welcome to StyliCleaner®
The solution to clean your CMM Styli automatically
In just 30 seconds!
Fast
In just 30 seconds, the CMM stylus is clean and ready to go back to work!
Easy
The StyliCleaner® is very easy and requires very little technical knowledge.
Reliable
The StyliCleaner® is very reliable as recalibration of all probe positions is no longer required!
Fully automatic
The StyliCleaner® cleans your CMM styli fully automatically, even during the measuring process!
Are you a 3D coordinate measuring machine operator?
Save time, and get the best results!
Work smarter not harder, let the StyliCleaner® clean your CMM styli fully automatic in only 30 seconds.
The combination of compressed air and cleaning detergent will remove the dirt from your CMM styli. Skip the time consuming process of manually cleaning and recalibration. Save your energy and be able to work more efficient.
The best part is yet to come, because all of this can take place during the measurement process!
Why should a StyliCleaner® be used?
On a 3D measuring machine, measurements can be carried out with very high accuracy on products. When checking an inner diameter, this diameter is usually calculated as an average diameter. There is a very high chance that a shaft with this average diameter does not fit in this hole. Calculating an average diameter is therefore not correct for a final check.
In this situation we should not calculate an average diameter, but the largest diameter that fits in this hole. We can compare this with a check using a pen caliber.
When calculating the largest enclosed diameter, then the diameter is calculated, which is tangent to 3 contact points.
When pollution is present on the product or on the stylus, this always has a major impact on the result of the calculation.
In practice, the large enclosed diameter is always smaller than the average diameter calculated.
For high accuracy diameters, a diameter is often specified with a small tolerance field on the diameter. Think for example of a diameter of Ø10H6. This diameter has a tolerance field of only 0.009mm. If with this diameter check a pollution of 0.003mm (is equal to 1/3 of the total tolerance field) is present, then an unjustified deviation in the actual diameter is observed.
Cleaning a product is of course very important, and can be carried out by a good working procedure.
However, cleaning a CMM stylus is a time consuming event. In practice, after manually cleaning a CMM stylus, these CMM stylus should always be calibrated. This calibration of a CMM stylus is also time-consuming. We should quickly think of at least 5 to 10 minutes. In some cases this remeasurement can take up to 1 hour.
During the calibration of the CMM stylus we cannot perform new product measurements. This is a pity of the time.
When this CMM stylus is cleaned with a StyliCleaner®, this cleaning action only takes 30 seconds. Besides the fact that this is much faster, it is also important that it can be done fully automatically. This is a double gain.
For this reason, the use of the StyliCleaner® is recommended.
This makes it much easier to perform measurements reliably.
This prevents valuable time being spent on product control which results in unreliable measurement results.
Among others the StyliCleaner® is successfully used on the following brands of measuring machines
In addition to being purchased directly, the StyliCleaner® can also be purchased from the dealers listed below. These dealers can also perform the installation if you prefer to have it done for you
Customize your StyliCleaner®!
This model, the SC2-SP, is a fully customized model made for Safran Group in France. The shaft is shortned to accomodate the right size for their CMM machine. In addition the cleaning chambers are both different in size. The upper cleaning chamber has the SC1 size and the cleaning chamber on the side matches the SC1S.
Whatever your dimensions are, we can design your StyliCleaner®.
Total package for specials:
- Cleaning unit
- Steering unit
- T-piece with 2 hose clamps to drain air from the CMM’s air hose
- Air hose for between T-piece and steering unit, 2 meter 6 mm
- Air hose for between steering unit and cleaning unit, 2 meter 4 mm
- Bolt m8x20 with washer for ficing the clesning unit to the table
- Hex key for the M8 bolt
- AC/DC adapter for feeding the steering unit with 24VDC
- Tieraps 10 pcs and 5 stickers to neatly hide cables
- 2 spare O-rings for the nebulizer
- Manual
Delivery time for customized specials is 6 weeks.
